Floor Hardeners

MC-Epo Floor T 50

Heavy Duty – Epoxy Mortar for Concrete Floors

MC-Epo Floor – T 50 is a synthetic compound consisting of a two parts epoxy system (resin & hardener) and a selected mix of fillers. MC-Epo Floor – T 50 is solvent free and non-toxic system to provide an excellent protection against wear, impact and chemical corrosion of acids alkalis, solvents, oils, salts and saline solution.

Key technical properties
MC-Epo Prime T 50 primer	200-300 g/m²
MC-Epo Floor T 50 mortar	2.00-2.25 kg/m² per 1 mm
MC-Epo Paint top coat	200-300 g/m²

Key technical properties
Colour	Available in a wide range of colours
Pot life @ 20-25°C	About 2 hours
Foot traffic	After about 24 hours
Light traffic	After 2-3 days
Heavy traffic	After 7 days
Complete cure @ 20-25°C	About 7 days
Solvent content	None
Density @ 25°C	2.0 g/cm³
Compressive strength - 7 days	680 kg/cm²
Flexural strength	300 kg/cm²

Key technical properties
Sulfuric acid	25% Excellent
Hydrochloric acid	20% Excellent
Phosphoric acid	40% Excellent
Citric acid	10% Excellent
Oxalic acid	10% Excellent
Acetic acid	10% Excellent
Sodium hydroxide	20% Excellent
Ammonia	15% Excellent
Solvents & mineral oils	- Excellent
Acetone	- Acceptable
Xylene	- Acceptable
Salt solutions	- Excellent

Description

MC-Epo Floor T 50 is a two-component epoxy mortar system - resin and hardener - combined with selected fillers. The source describes it as solvent-free and suitable for high protection against abrasion, impact and chemical corrosion.

Where to use

Oil refineries, workshops, garages and ramps. Chemical and pharmaceutical plants, battery rooms and power plants. Laboratories, laundries and paper mills. Food industries, mills, bakeries and slaughterhouses. Industrial production halls, warehouses and plating plants.

Advantages

Excellent abrasion and impact resistance. Excellent chemical resistance. Suitable for environments requiring high hygiene standards. Used for new concrete floors and restoration of old floors exposed to corrosive atmospheres and severe service. Can be applied on horizontal, vertical or inclined surfaces. Provides a seamless, dust-free floor that can be cleaned to a high standard. High compressive and flexural strength.

Application rates

MC-Epo Prime T 50 primer 200-300 g/m² MC-Epo Floor T 50 mortar 2.00-2.25 kg/m² per 1 mm MC-Epo Paint top coat 200-300 g/m²

Chemical resistance

Material Concentration Resistance Sulfuric acid 25% Excellent Hydrochloric acid 20% Excellent Phosphoric acid 40% Excellent Citric acid 10% Excellent Oxalic acid 10% Excellent Acetic acid 10% Excellent Sodium hydroxide 20% Excellent Ammonia 15% Excellent Solvents & mineral oils - Excellent Acetone - Acceptable Xylene - Acceptable Salt solutions - Excellent

Application procedure

Surface preparation: the substrate must be clean, dry and free from dust, oil, grease and defects. Repair honeycombs and holes before application. Priming: mix MC-Epo Prime T 50 components thoroughly and apply by roller, brush or a suitable tool. Allow the primer to become tacky. Mixing: mix MC-Epo Floor T 50 components with a low-speed mixer for 3-5 minutes until homogeneous. Application: spread the mortar at approximately twice the required thickness, compact manually or mechanically, strike off excess, then finish with a steel trowel for a dense, smooth surface. For a very smooth, glossy finish and increased chemical resistance, the source recommends sealing the mortar with MC-Epo Paint in the required colour. Service: foot traffic after about 24 hours, moderate traffic after about 3 days and heavy traffic after 7 days.

MCT / SYSTEMS